生產的中空玻璃加工設備可以高能地完成中空玻璃的生產，在中空玻璃加工行業里享有很高的聲譽。俗話說，沒有規矩不成方圓，所有設備都有自己的操作規程和規范。操作員在操作中空玻璃生產線的時候，要嚴格按照中空玻璃加工設備的操作規程來做，那么中空玻璃加工設備的操作規程有哪些，請注意下面幾條：
The insulating glass processing equipment can complete the production of insulating glass with high energy, and enjoys a high reputation in the insulating glass processing industry. As the saying goes, there is no square without rules. All equipment has its own operating procedures and specifications. When operating the insulating glass production line, the operator shall strictly follow the operating procedures of the insulating glass processing equipment. What are the operating procedures of the insulating glass processing equipment? Please pay attention to the following:

1.中空玻璃生產線開機順序：首先要檢查中空玻璃加工設備水箱里的水充足，然后打開水泵，調整白色海綿輥上方的噴水管，保證海綿輥所有位置都能被沖洗到。然后用手將海綿輥上的雜質和臟物清洗干凈，并且保證海綿輥被完全泡開泡膨脹。注意在冬天開啟中空玻璃生產線時，一定不要先打開清洗傳送。因為冬天兩個緊鄰的海綿輥會被凍在一起，在沒有被浸泡開的情況下打開傳送，會導致海綿輥被撕壞。

1. Startup sequence of insulating glass production line: first check that the water in the water tank of insulating glass processing equipment is sufficient, then turn on the water pump and adjust the water spray pipe above the white sponge roller to ensure that all positions of the sponge roller can be flushed. Then clean the impurities and dirt on the sponge roller by hand, and ensure that the sponge roller is completely foamed and expanded. Note that when opening the insulating glass production line in winter, do not open the cleaning conveyor first. Because two adjacent sponge rollers will be frozen together in winter, opening the transmission without being soaked will cause the sponge roller to be torn.
2.然后打開清洗傳送，將待加工的中空玻璃放在傳送輪上，注意玻璃一定要放平穩，防止玻璃在傳送過程中掉落傷到人。
2. Then open the cleaning conveyor, place the hollow glass to be processed on the conveyor wheel, and pay attention to the glass must be placed stably to prevent the glass from falling and hurting people during transmission.
3.鋁隔條上涂抹的丁基膠要保證均勻，而且涂抹在整個鋁條表面，防止漏膠，有毛刺現象。并且采用優良丁基膠保證鋁條和玻璃結實的站合在一起。鋁隔條涂完膠后禁止有粘上灰塵。
3. Butyl glue applied on the aluminum spacer strip shall be uniform and applied on the whole surface of the aluminum strip to prevent glue leakage and burr. And it adopts excellent butyl glue to ensure that the aluminum strip and glass stand together firmly. It is forbidden to stick dust on the aluminum spacer after coating.
4.雙組份密封膠要涂抹牢固，表面保持平滑，尤其是拐角處要涂抹好，防止漏氣，跑氣現象。
4. The two-component sealant shall be applied firmly and the surface shall be smooth, especially at the corners to prevent air leakage and air escape.