很多中空玻璃生產線客戶反應，購買中空玻璃生產線后，由中空玻璃生產線廠家派人調試，但是，不知道如何確定中空玻璃生產線已經調試完備，正常生產，在這里，威力智能本著為客戶負責，將調試過程全盤公布，希望為大家解惑：
Many customers of the insulating glass production line reported that after purchasing the insulating glass production line, the manufacturer of the insulating glass production line sent someone for debugging. However, I don't know how to determine that the insulating glass production line has been fully debugged and produced normally. Here, Weili intelligence is responsible for the customer and announces the whole debugging process. I hope to solve your doubts:
1、將中空玻璃生產線輕置于安裝位,正確擺放生產線各段的位置次序.
1. Place the insulating glass production line lightly at the installation position and correctly place the position order of each section of the production line
2、將中空玻璃生產線的機身調平.調整機器底座上調平螺栓高度,使傳送輥、支撐尼龍輪支撐面等高,斜架上的背靠輪共面,各段相對平行,然后鎖緊螺母.

2. Level the machine body of the insulating glass production line, adjust the machine base, adjust the height of the leveling bolt, make the supporting surface of the conveying roller and the supporting nylon wheel equal, the back-up wheels on the inclined frame are coplanar, and each section is relatively parallel, and then lock the nut

3、將中空玻璃生產線各段間需聯接的部位聯接緊固,聯接好由入料段到清洗干燥段的傳動鏈條.正確擺放風機及水箱,并按水路、風路系統圖接好風管、水管.
3. Fasten the parts to be connected between the sections of the insulating glass production line, connect the transmission chain from the feeding section to the cleaning and drying section, correctly place the fan and water tank, and connect the air pipe and water pipe according to the water and air circuit system diagram
4、全 面檢查中空玻璃生產線所有緊固件連接處是否因運輸震動而松動,并逐件緊固(特別是各接線端子連接處是否松動).
4. Comprehensively check whether all fastener connections of the insulating glass production line are loose due to transportation vibration, and tighten them one by one (especially whether the connections of each wiring terminal are loose)
5、接地線用截面積不小于4平方毫米的軟銅心黃綠絕緣線,接地電阻不大于4歐姆.
5. The grounding wire shall be soft copper core yellow green insulated wire with a cross-sectional area of not less than 4mm2, and the grounding resistance shall not be greater than 4 ohms
接通氣源檢查管路是否通暢,有無破損.氣源壓力要求0.6~0.8Mpa.接通電源試驗中空玻璃生產線各電機的旋轉方向是否正確,各段傳動鏈輪是否靈活、平穩.整機清潔,整理工作區間.
Connect the air source and check whether the pipeline is unobstructed and damaged. The air source pressure is required to be 0.6 ~ 0.8MPa. Connect the power supply and test whether the rotation direction of each motor of the insulating glass production line is correct and whether the transmission sprocket of each section is flexible and stable. Clean the whole machine and sort out the working range
以上就是我們調試人員所需要做并且確定做到的中空玻璃生產線的調試，選擇中空玻璃生產線，還是選擇真 正的廠家，只有真 正的廠家，價格才能優惠，性價比才會更好，畢竟沒有一個廠家生產出中空玻璃生產線，是奔著自己倒閉的，您說呢，中空玻璃生產線廠家還是選擇威力智能，質量優，運行穩定可靠。
The above is what our commissioning personnel need to do and decide to do. Choose a hollow glass production line or a real manufacturer. Only a real manufacturer can have preferential prices and better performance price ratio. After all, no manufacturer has produced a hollow glass production line and is going bankrupt. What do you say, The manufacturer of insulating glass production line still chooses power intelligence, excellent quality and stable and reliable operation.